Create It Yourself

Hang‘em Up – With This Space Saving Pot Rack

Show off your cookware with this unique overhead kitchen pot rack

Print Page
pot_rack

An overhead pot rack is a convenient way to keep your cooking equipment at the ready. A kitchen pot rack is also ideal for showing off a beautiful set of copper pots or a collection of antique cookware. Even your everyday pots and utensils will look good hanging from a rack.

Gathering Materials

This simple rack uses standard building materials and can be completed in about four hours, not counting drying time for glue and wood finishes. Options for materials are fairly wide-open. The wood rails can be hardwood (such as oak or maple) or a softwood (such as pine). Use “clear” timber without large knots, which create weak spots and are difficult to drill through. For the pipe rungs of the rack, rigid copper water pipe is smooth, attractive and easy to work with. You can also use metal “thin-wall” electrical conduit if you prefer its silver colour.

  1. Overhead Kitchen Pot Rack 03

    Determine the desired size (length and width) of your rack based on your kitchen space and number of pots you’d like to hang. The rack shown here is approximately 914x533mm. Plan the rung layout using even spacing between rungs and leaving a couple of inches between the outer rungs and the wood end rails.

    TIP: Extend the long side rails beyond the end rails and make a decorative cut on the side rails.

  2. Overhead Kitchen Pot Rack 04

    Cut the two side rails and two end rails to length from 1 x 3 lumber, using a BLACK+DECKER 20V MAX* 5-1/2 in. Circular Saw. Make the side rails equal to the overall length of the rack. Make the end rails 1 1/2" shorter than the overall width of the rack. Cut three rung supports from 1 x 2 lumber. These run parallel to the side rails and should fit snugly between the end rails when the rack is assembled.

    TIP: Test-fit all of the cut wood parts by dry-assembling the rack (no glue or screws). If desired, shape the ends of the side rails by cutting a taper with a circular saw or cutting curved lines with a jigsaw.

  3. Overhead Kitchen Pot Rack 05

    Cut the pipe rungs to length, using a reciprocating saw. Make the rungs 3mm shorter than the length of the 25x76mm end pieces. Lightly sand the cut ends with sandpaper to remove any burrs or sharp edges.

    TIP: Polish the rungs with wire wool to shine them up. You can remove printed lettering with fine sandpaper, or simply position the rungs so the lettering isn’t visible from below when the rack is installed.

  4. Overhead Kitchen Pot Rack 06

    Mark the rung holes onto the face of one of the 25x50mm rung supports. The holes should be spaced evenly and centred top-to-bottom on the rung support. Stack the three rung supports together, with the marked piece on top, and place the stack face down on top of a piece of scrap timber, such as a flat 50x100mm that runs the length of the stack. Make sure the support pieces are flush with one another, then clamp the stack securely to a work surface, using three clamps. Drill each rung hole through the stack and partially into the scrap timber, using your drill driver and 75/100mm spade bit. This setup helps ensure clean holes without splintering. Keep the drill bit perfectly vertical while drilling to produce straight holes.

  5. Overhead Kitchen Pot Rack 07

    Sand all wood surfaces that will be exposed in the finished project using a sander. Do not sand the ends of the pieces that will be joined at the rack’s corners. You want sharp edges here for tightly fitting joints.

  6. Overhead Kitchen Pot Rack 08

    Glue a rung support to the inside face of each side rail, using wood glue and clamps. The supports should be centred end-to-end on the rails and flush with the rails’ bottom edges. Once the pieces are clamped, drill pilot holes and drive a few 32mm finish nails through the inside faces of the rung supports and into the rails. Let the glue dry as directed before removing the clamps.

  7. Overhead Kitchen Pot Rack 09

    If desired, you can paint or stain the wood parts before assembling the rack. This saves time and prevents you from having to tape off each rung to keep it free of paint. Do not finish the ends of the rung supports or end rails or the areas where these pieces will meet the side rails/end rails when the rack is assembled. These joints will be glued, and the glue needs bare wood for a strong bond.

    Tip: Finish the rack with a clear varnish to retain the wood’s natural colouring.

  8. Overhead Kitchen Pot Rack 10

    Insert all of the rungs through the holes in the centre rung support, and then fit the side rails over the ends of the pipes. Position the end rails between the side rails so their inside faces are butted against the ends of the centre rung support. Clamp the assembly with pipe clamps (if you have them), or have a helper hold each joint as you work. Drill two evenly spaced pilot holes through the side rail and into the end of each end rail. Do the same where the end rails meet the centre support. Disassemble the rack, then apply glue to the ends of the rung supports and end rails. Reassemble and clamp the rack, then secure each joint with 57mm wood screws. Let the glue dry overnight.

  9. Overhead Kitchen Pot Rack 11

    Fill the screw holes with wood putty if your rack is painted. Or, cover the holes with wood plugs or decorative wood buttons, glued in place, if you’re using a clear varnish. Paint over the wood putty and touch up any other areas that need it.

  10. Overhead Kitchen Pot Rack 12

    Locate the ceiling joists in the installation area, using a detector and mark the centres of the joists. You can also install the rack along a single joist that runs parallel to the length of the rack. Drill a pilot hole and install a heavy-duty screw hook into the joist for each end of the rack, using pliers. Install corresponding screw hooks into the top edges of the rack’s side rails (not the end rails), one hook for each corner. Cut lengths of chain to hang the rack at the desired height, using a hacksaw or a rotary tool or multi-tool with a metal-cutting blade. Hang the rack by hooking the chains onto the screw hooks. Add S-hooks to the rungs for hanging your pots and utensils.

    TIP: If you’re hanging the rack from two joists, you can use four chains and ceiling hooks instead of two, whichever look you prefer.

    WARNING: Always anchor the rack into ceiling joists or solid-timber blocking installed between the joists. A ceiling finish alone will not support a rack, even if you use toggle bolts or other hollow-wall anchors.

Hang‘em Up – With This Space Saving Pot Rack